耐酒精五金油墨销售厂家
本产品主要用于各种金属、玻璃、真空电镀、水电镀、电泳、阳极氧化铝、电解板、铝塑板、喷塑、喷粉、静电喷漆面、烤漆面以及各种天花吊顶氧化板、镜面板、覆膜板、辊涂板、尼龙加玻纤、三聚--胺板,uv表面,木板烤漆面等等制品的丝印及移印。
2、产品特性：亮光、附着力佳、快干、耐冲压。
3、稀释剂：用我司b-03稀释剂或783开油，用718洗网水清洗网版。
4、固化剂：单组份使用，也可选择添加我司js-10固化剂用于增加油墨附着力及物理化学抗性。
5、油墨调配方法：开罐先搅拌均匀，取所需量油墨稀释到合适印刷粘度。如需添加固化剂，先加固化剂搅拌后静置10分钟，待油墨与固化剂完全交联后再进行稀释。
6、干燥时间：常温干燥，表干时间5-10分钟，实干时间在24小时以内，80℃烘烤20分钟可快速干燥。
7、添加固化剂后的使用时限：4-6小时，过期请弃用，剩余油墨不可回收。
性能检测
1、3m胶带划百格测试：100%无脱落
2、耐冲压测试：1mm厚铝板180°折弯无变化。
3、耐酒精测试：用脱脂棉沾浓度99%工业酒精以500g力水平来回200次无脱色。
注意事项
1、先小量试印确认符合要求后再批量生产。
2、做好承印物的表面清除油脂及杂质工作，以促进附着效果。
3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测，
需要完全固化后方可检测。
4、未经允许情况下，不得将本系列油墨与其它类型油墨混用及配色。
5、油墨，稀释剂使用及储存时严禁烟火。
6、使用时注意施工场所的通风状况良好，尽量避免皮肤直接接触。
7、本品不慎溅入口、鼻、眼、耳内，应用大量水清洗或直接求助医生。
8、技术参考数见下表：
检验项目 检验结果 测试条件
油墨线度 ≤12um 刮板细度计
干膜光泽 ≥65° 60°镜面光泽计
干燥速度 表干 25℃×5-10min 或60℃×2-3min
实干 25℃12hr或60℃×10min
耐酒精性 无变化 500克力/cm2酒精棉200次来回
附着力 100/100 1mm×1mm×100格3m胶纸剥离
耐酸性 无变化 浸泡5%hci×24hr
耐碱性 无变化 浸泡5%naoh×24hr
耐盐性 无变化 浸泡5%naci×24hr
耐水性 无变化 浸泡20℃自来水×96hr
耐磨性 不见底 500克/cm2负载含砂橡皮200来回
耐热性 无变化 80℃×12hr
the products are mainly used in screen printing&the printing of various kinds of metal, glass, vacuum plating, electroplating, electrophoresis, water anodic alumina, electrolytic plate, aluminum plate, plastic spraying, dusting, electrostatic spray painting, paint su-ce&various ceiling oxide board, mirror panels, coated board, roller coated board&other products.
2, product characteristics: light, good adhesion, fast drying, stamping resistance.
3, diluent: with our b-03 special thinner/783 open oil, washing network water cleaning screen with 718.
4, curing agent: one component use, can also choose to add our js-10 special curing agent is used to increase the ink adhesion&physical&chemical resistance.
5, printing ink allocation methods: open cans to stir well, take appropriate amount needed to dilute ink printing viscosity. if you need to add curing agent, first add curing agent after mixing&set aside for 10 minutes,&curing agent for ink completely crosslinking after dilution.
6, the drying time: dry, dry time table for 5-10 minutes, work time within 24 hours, 80 degrees bake for 20 minutes can be dried quickly.
7, adding curing agent after the use of time: 4-6 hours, expired please abandoned, residual ink unrecyclable.
[detection] performance
1, 3m tape row adhesion test: 100% without shedding
2, stamping resistance test: 1mm thick aluminum 180 degree bend without change.
3, alcohol resistant test: with cotton dipped in 99% alcohol concentration of industry to 500g stress level&back 200 times without decolorization.
[note]
1, the first small try printing again after confirmation of compliance with the requirements of mass production.
2, do a good job in the substrate su-ce to remove grease&impurities, in order to promote the adhesion effect.
detection of 3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scr---h resistance, abrasion resistance&other properties,
fully cured before detection.
4, without permission, may not use the series of ink&other types of ink mixing&m---hing.
5, ink, fireworks is strictly prohibited the use of thinner&storage.
6, the use of ventilation conditions attention the construction site is good, try to avoid direct contact with skin.
7, this product is inadvertently splashed entrance, nose, eyes, ears, use a large number of water washing/direct help doctor.
